AMT Datasouth Fastmark M6 PLUS Series Betriebsanweisung Seite 1

0 Fastmark M1/203dpi Direct Thermal Barcode Printer User’s Guide Document #120103 A

6 3. Place the roll between the holders and close them onto the core. 4. Place the media, printing side face up, through the media guides, over

7 5. Close the top cover gently and make sure the cover latches securely. 6. Use “Diagnostic Tool” to set the media sensor type and calibrate th

8 3.2.2 Loading External Media 1. Open the printer’s top cover and separate the media holders to fit the media width. 2. Press down the media holde

9 3.2.3 Loading Media in Peel-off Mode (Optional) 1. Refer to section 3.2.1 to load the media. 2. Open the top cover and peel-off panel after calib

10 4. Push the peel-off panel back to the printer. 5. Close the top cover gently. 6. Press the FEED button to test. Note: Please calibrate t

11 3.2.4 Loading Media in Cutter Mode (Optional) 1. Refer to section 3.2.1 to load the media. 2. Lead the media through the cutter paper opening.

12 3.3 Diagnostic Tool The Diagnostic Utility is enclosed in the CD disk \Utilities directory. The Diagnostic Utility is a toolbox that allows users

13 3.3.2 Printer Function (Calibration/setup) 1. Select the PC interface connected with bar code printer. 2. Click the “Function” button to setting

14 3.4 Setting Ethernet by Diagnostic Utility (Optional) The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagn

15 3.4.2 Using Ethernet interface to setup Ethernet interface 1. Connect the computer and the printer to the LAN. 2. Turn on the printer power. 3.

i Contents Copyright Declaration... i 1. Introduc

16 7. Click “Change IP Address” to configure the IP address obtained by DHCP or static. The default IP address is obtained by DHC

17 3.5 Install Micro SD Memory Card 1. Open the SD memory card cover located on the left side of the printer. 2. Insert the MicroSD card into the

18 3.6 Mount the Printer on the Wall There are three holes in the bottom of printer. The printer can be mounted on the wall with 1/8” head screws

19 4. LED and Button Functions This printer has one button and one three-color LED indicator. By indicating the LED with different color and pressin

20 3. Printer initialization Release 4. Set black mark sensor as media sensor and calibrate the black mark sensor Release 5. Set gap sen

21 Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be used to check if there

22 Note: 1. Dump mode requires 2” wide paper width. 2. Turn off / on the power to resume printer for normal printing. 3. Press FEED button to bac

23 4.3.4 Set Media Black Mark Sensor and Calibrate Please follow the steps as below. 1. Turn off the power switch. 2. Hold on the button then turn

24 5. Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printe

25 5.2 Print Problem Problem Possible Cause Recovery Procedure Not Printing Check if interface cable is well connected to the interface connector.

i Copyright Declaration Information in this subject to change without notice and does not represent a commitment on the part of AMT Datasouth Corpo

26 5.3 LCD display This section lists the LCD display messages that you may encounter when operating the printer. Also, it provides solutions. M

27 6. Maintenance This session presents the clean tools and methods to maintain your printer. 1. Please use one of following material to clean t

28 Corporate Headquarters Manufacturing/Service 803 Camarillo Springs Road, Suite-D 5033 Siro

ii CAUTION 1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER BODY PARTS AWAY. 2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HA

1 2. Operations Overview 2.1 Unpacking and Inspection The Fastmark M1 printer has been specially packaged to withstand damage during shipping. Ple

2 2.2 Printer Overview 2.2.1 Front View 1. Top cover open lever 2. MicroSD card socket 3. Media view window 4. LED indicator 5. Feed button

3 2.2.2 Interior View 1. Top cover 2. Media holder 3. Media guide 4. Printhead 5. Gap sensor (receiver) 6. Gap sensor (transmitter) 7. Platen

4 2.2.3 Rear View 1. Power switch 2. Power jack socket 3. USB interface 4. RS-232C interface (Optional) 5. Fan-fold paper entrance chut

5 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is set to “off”. 3. Connect the